亚洲国产精品久久不卡毛片_yyyy11111少妇无码影院_国产九九九九九_国产精品免费av_精品国一区二区三区_乱码专区一卡二卡国色天香

歡迎來到東莞市艾維品實業有限公司官網!

東莞市艾維品實業有限公司

專業研發、生產、銷售各種花紋的水轉印膜

全國咨詢熱線

400-0253-888

新聞資訊

新聞中心

當前位置: 首頁 > 新聞中心 > 龍泉公司新聞

龍泉水轉印加工技術操作方法

2023-06-02 09:02:52
1343次

1. 確定適當水溫 (20 °C – 30°C),水面保持溢流狀態。

Make sure the proper water temperature (20 °C - 30 °C), keep water at overflow state.


2. 保持水表面無活化劑殘留及雜質。

Keep the water surface without activator residues and impurities.


3. 置膜,以適當角度將膜平放于水面(確定膜之正反面,印刷層朝上)

Put the film on the water flatly with the proper angle.( Confirm the film positive & negative, printing side up)


4.配合水溫設定溶解時間,水溫一般為25-30度,溶解時間約為45秒到2分鐘

Set dissolution time with water temperature which is often 25°C-30 °C. The dissolution time is about 45 seconds to 2 minutes.


5.視印刷油墨之厚度,判定噴涂活化劑之時間,油墨層越厚,可在膜尚未完全溶解時,提前噴涂活化劑,讓油墨活化時間加長,而一般作業情況溶解1分鐘左右可噴涂活化劑,待膜成鏡面而平坦擴展(5秒-15秒)即可上膜、轉印。

Spray activator time depends on the thick of printing ink. The thicker the ink layer, spray activator in advance before the film not yet completely dissolved, to make the ink activate time much longer. General operation condition is about 1 minute to dissolve, then spray activator. After flat extension of the film (5 seconds -15 seconds), then put the film to be printed and transferred .


6. 在上膜之前需視加工物之外形或有紋路性,選擇下水角度,以利于空氣排出。

Select water down angle to exhaust air well as the dip items' shape or lines prior to film transfer . 


7. 上膜后,不可立即拿起,應在水中搖晃3-5秒,切斷邊緣之膜,增加紋路咬住被加工物之時間。

Do not take out the work piece immediately after transfer the film. Shake it on the water for 3-5 seconds, to cut the edge's film and increase the lines to bite work piece's time.


8. 活化劑噴涂需以0.8mm*4孔噴槍及可攪拌式壓力操作業,噴涂距離約30cm,空氣壓力適當調整避免花紋脫落,不可有水花產生,必要時水溫可加到35°C, 水槽之水量需作溢, 最后一道水需干凈,沖洗完成需經空氣吹干并經品管修整再入烘烤爐。

Spray activator with 0.8mm * 4 hole spray gun and operate by stirred pressure. Spray distance is about 30cm. Adjust air pressure properly to avoid the film pattern fall off, and water can't be splashed. Add water temperature to 35 °C if necessary. The tank water is overflow and the last water must be clean. After rinse, then dry by oven. 


不同的圖案,必須使用不同的底色,如木紋基本使用棕色、咖啡色、土黃色等,石紋基本使用白色等.

 Different film pattern , different base coat. e.g. Wood grain (often Brown, khaki), Marble grain (often white etc).


近期瀏覽:

相關新聞

contact us

東莞市艾維品實業有限公司

廣東省東莞市樟木頭鎮金河社區濱河路31號

水轉印膜丨水轉印耗材丨水轉印設備

水轉印產品代加工丨水轉印技術支持

水轉印開發、生產、加工、銷售、培訓一條龍服務

contact us

         


         掃一掃 添加微信

SERVICE

聯系人:(董先生)

133-7860-9888

全國熱線

400-0253-888

座機

0769-81723888

0769-87123588

24小時在線客服
主站蜘蛛池模板: 一区二区在线免费观看 | 四虎影视国产在线视频 | 国产成人精品免费大全 | 国产在线欧美 | 亚洲 欧美日韩 国产 中文 | 风起洛阳在线观看免费西瓜影视 | 国产又色又爽又黄又免费 | 亚洲日韩欧美一区二区在线 | 狠狠干视频网 | 国产精品麻 | 亚洲欧美一区二区三区久久 | 91精品国产91久久久久久密臀 | 国产视频手机在线观看 | 精品欧美小视频在线观看 | 99久久久免费精品国产一区二区 | 免费看一级毛片 | 成人一区二区在线观看 | 成年网站在线 | 午夜影院黄色一级片 | 国产精品久久久久久久久久性按摩 | 久久精品视 | 99热这里只有精品在线 | 欧美一二区在线观看 | 国产黄a三级三级三 | 在线观看免费的av | 成人性生交大片免费4 | 午夜3点看的视频 | 亚洲国产精品午夜久久久 | 日韩 欧美 亚洲 国产 | 国产女做a爱免费视频 | 国产精品一区二区三区乱码 | 日本另类αv欧美另类aⅴ | 欧美一区激情视频在线观看 | 国产精品久久艹 | 日韩美女视频一区 | 秀人顶级模特尤妮丝的最新视频 | 手机国产乱子伦精品视频 | 狂野的爱在线观看 | 国产亚洲精品久久久久无码 | 国产69精品久久99不卡的观看体验 | 日韩中文字幕无砖 |